Transmitter Reference Design for a 900MHz Full-Duplex Radio

Abstract: This reference design covers the design of a transmitter inside a 900MHz full-duplex radio using the MAX2902 single-chip transmitter. The MAX2902 is designed for use in the 869MHz to 915MHz frequency band, and complies with FCC CFR47 part 15.247 902MHz to 928MHz ISM band specifications. The reference design is capable of delivering more than +19dBm with V_CC= 2.9V and I_CC= 170mA, and +20dBm with V_CC= 3.3V and I_CC= 190mA, while meeting 14dB of CNR (1.22Mbps BPSK) at 10:1 VSWR (all angles).




Figure 1. Reference design board features the MAX2902 single-chip transmitter, which is designed for use in 868MHz to 915MHz frequency band. The device complies with FC CFR47 part 15.247 902MHz to 928MHz ISM band specifications.



More detailed /static/ic5/dianlu/image (PDF, 213kB)
Figure 2. Reference design block diagram for the MAX2902 900MHz BPSK transmitter. Shows characterization report (v1b), block diagram, and interface connects. Dedicated LDO for Tx IC VCO and TCXO is to mitigate coupling from PA. The second LDO output supplies the synthesizer and the Tx IC (all but the PA). The transmitter's PA is supplied directly by the system (V_{CC_MAIN}). An additional PA is required to get > 18dBm output power while meeting 20% EVM requirement at 8:1 VSWR. The 40MHz WLAN TCXO was used as a temporary replacement for the intended 16.36MHz GPS reference originally specified. The PLL can accommodate any common reference frequency from 1MHz to 50MHz. The customer should select their TCXO based on cost and tolerance for phase noise of the unmodulated carrier.

Lab Measurements

System Performance Summary
Measured at ANT RF SMA; V_CC= 3.3V; T_A= +25°C; REF-OSC Freq = 40MHz; PLL locked at 900MHz; LDOEN = high; CSB = high; SCLK = DIN = Low; 2.5V_P-P1.0Mbps PN bit stream (unfiltered) applied to BPSK input, unless otherwise noted.

Parameter	Conditions and Comments			Target	Measured	Units
Supply Current	Shutdown mode (LDOEN = LOW), VCC= 4.5V (worst case)				1.7	µA
	For +17.5dBm at LPF output (VASK= 2.1) Includes LMX2353 synthesizer and TCXO supply current.			141	104	mA
Tuning Range	Range of VCO, freq determined by PLL			902 to 928	902 to 928	MHz
LO Integrated Phase Error	In 2MHz BW of demodulator, no modulation				1.6	°RMS
Phase EVM	EVM contribution from the above RMS phase error (for small angles, approximate EVM by ΦERR/(360/2pi)				2.8	%
Magnitude EVM	No modulation				0.2	%
	1.0Mbps PN sequence BPSK modulation				13 to 14	%
Full-Power EVM	VASK= 2.1V, 8:1 VSWR (worst-case angle) Dominated by distortion due to VCO pulling	VCC_MAIN= 2.7V, ICC= 106mA (50Ω pwr = +16.9dBm)		20	40.2	%
		VCC_MAIN= 3.3V, ICC= 114mA (50Ω pwr = +19.2dBm)		20	43.6
		VCC_MAIN= 4.0V, ICC= 138mA (50Ω pwr = +20.6dBm)		20	53.3
		VCC_MAIN= 4.5V, ICC= 299mA (50Ω pwr = +21.3dBm)		20	30.1
Output Power	50Ω load, 1.0Mbps BPSK modulation (Power at balun output is approx 1dB higher, due to BPF, T-line, SMA) EVM for specified VSWR (worst-case phase angle) is less than 20%	VASK= 2.1V (for 1:1 VSWR tolerance)	VCC_MAIN= 2.7V, ICC= 103mA		16.9	dBm
			VCC_MAIN= 3.3V, ICC= 133mA	17.5	19.2
			VCC_MAIN= 4.0V, ICC= 141mA		20.6
			VCC_MAIN= 4.5V, ICC= 145mA		21.3
		VASK= 1.7V (for 4:1 VSWR tolerance)	VCC_MAIN= 2.7V, ICC= 103mA		16.7
			VCC_MAIN= 3.3V, ICC= 108mA		18.2
			VCC_MAIN= 4.0V, ICC= 112mA		19.0
			VCC_MAIN= 4.5V, ICC= 114mA		19.4
		VASK= 1.6V (for 8:1 VSWR tolerance)	VCC_MAIN= 2.7V, ICC= 95mA		16.2
			VCC_MAIN= 3.3V, ICC= 99mA		17.2
			VCC_MAIN= 4.0V, ICC= 102mA		17.8
			VCC_MAIN= 4.5V, ICC= 104mA		18.1
Reference Spurs	fCOMP= 2MHz, worst-case condition: VCC= 4.5V, +21.3dBm output power Actual measurement was < -63dBc (below noise floor of VSA)			< -41	< -42	dBm/MHz
Output Harmonics	2ndharmonic levels, at LPF output (limit is -27dBm/MHz in nonrestricted bands)			< -30	-42	dBm/MHz
	3rdharmonic levels, at LPF output (limit is -41dBm/MHz in restricted bands)			< -49	-54

Measurement Data