edd1216aata-5
数据 薄板 e0443e40 (ver. 4.0)
13
command 运作
command 真实 表格
ddr sdram 认识 这 下列的 commands 指定 用 这 /cs, /ras, /cas, /我们 和 地址 pins. 所有 其它
结合体 比 那些 在 这 表格 在下 是 illegal.
CKE
Command 标识 n – 1 n /cs /ras /cas /我们 BA1 BA0 AP 地址
ignore command DESL H H H
×
×
×
×
×
×
×
非 运作 NOP H h l h h h
×
×
×
×
burst 停止 在 读 command BST H H L H H L
×
×
×
×
column 地址 和 读 command 读 H H L H L H V V L V
读 和 自动-precharge reada h h l h l h v v h v
column 地址 和 写 command WRIT H H L H L L V V L V
写 和 自动-precharge WRITA H H L H L L V V H V
行 地址 strobe 和 bank 起作用的 ACT H H L L H H V V V V
precharge 选择 bank 前 H H L L H L V V L
×
precharge 所有 bank PALL H H L L H L
×
×
H
×
Refresh REF H h l l l h
×
×
×
×
自 H l l l l h
×
×
×
×
模式 寄存器 设置 MRS H h l l l l l l l v
EMRS H h l l l l l h l v
remark: h: vih. l: vil.
×
: vih 或者 vil v: 有效的 地址 输入
便条: 这 cke 水平的 必须 是 保持 为 1 ck 循环 在 least.
ignore command [desl]
当 /cs 是 高 在 这 交叉 要点 的 这 ck rising 边缘和 这 vref 水平的, 每 输入 是 neglected 和 内部的
状态 是 使保持.
非 运作 [nop]
作 长 作 这个 command 是 输入 在 这 交叉 要点 的 这 ck rising edge 和 这 vref 水平的, 地址 和 数据
输入 是 neglected 和 内部的 状态 是 使保持.
burst 停止 在 读 运作 [bst]
这个 command stops 一个 burst 读 operation, 这个 是 不 适用为 一个 burst 写 运作.
column 地址 strobe 和 读 command [read]
这个 command 开始 一个 读 运作.这 开始 地址 的 这 burst 读是 决定 用 这 column 地址
(看 “address 管脚 table” 在 管脚 函数) 和 这 bank 选择地址. 之后 这 completion 的 这 读 运作,
这 输出 缓存区 变为 高-z.
读 和 自动-precharge [reada]
这个 command 开始 一个 读 运作. 之后 completion 的这 读 运作, precharge 是 automatically executed.
column 地址 strobe 和 写 command [writ]
这个 command 开始 一个 写 运作.这 开始 地址 的 这 burst 写 是 决定 用 这 column 地址
(看 “address 管脚 table” 在 管脚 函数) 和 这 bank 选择 地址.
写 和 自动-precharge [writa]
这个 command 开始 一个 写 运作. 之后 completion 的这 写 运作, precharge 是 automatically executed.