NX29F010
6
nexflash 科技, 公司
nxpf001f-0600
06/22/00 ©
硬件 数据 保护
这 command sequence 必要条件 的 unlock 循环 为
程序编制 或者 erasing 提供 数据 保护 相反
inadvertent 写 (谈及 至 这 command 定义 表格).
在 增加, 这 下列的 硬件 数据 保护 mea-
sures 阻止 意外的 erasure 或者 程序编制, 这个
might 否则 是 造成 用 spurious 系统 水平的
信号 在 v
CC
电源-向上 和 电源-向下 transitions, 或者
从 系统 噪音.
写 脉冲波 "glitch" 保护
噪音 脉冲 的 较少 比 5 ns (典型) 在
OE
,
CE
, 或者
我们
做 不 initiate 一个 写 循环.
logical inhibit
写 循环 是 inhibited 用 支持 任何 一个 的
OE
= v
IL
,
CE
= v
IH
, 或者
我们
= v
IH
. 至 initiate 一个 写 循环,
CE
和
我们
必须 是 一个 logical 零 当
OE
是 一个 logical 一个.
电源-向上 写 inhibit
如果
我们
=
CE
= v
IL
和
OE
= v
IH
在 电源-向上, 这 设备
做 不 接受 commands 在 这 rising 边缘 的
我们
. 这
内部的 状态 机器 是 automatically 重置 至 读
排列 数据 在 电源-向上.
command 定义
writing 明确的 地址 和 数据 commands 或者 sequences
在 这 command 寄存器 initiates 设备 行动. 这
command 定义 表格 5 定义 这 有效的 寄存器
command sequences. writing incorrect 地址 和 数据
值 或者 writing 它们 在 这 improper sequence resets 这
设备 至 读 排列 数据.
所有 地址 是 latched 在 这 下落 边缘 的
我们
或者
CE
,
whichever 发生 后来的. 所有 数据 是 latched 在 这 rising
边缘 的
我们
或者
CE
, whichever 发生 第一. 谈及 至 这
适合的 定时 图解 在 这 "交流 特性"
部分.
读 排列 数据
这 设备 是 automatically 设置 至 读 排列 数据 之后
设备 电源-向上. 非 commands 是 必需的 至 retrieve
数据. 这 设备 是 也 准备好 至 读 排列 数据 之后
完成 一个 embedded 程序 或者 embedded 擦掉
algorithm.
这 系统 必须 公布 这 重置 command 至 re-使能 这
设备 为 读 排列 数据 如果 这 错误 状态 位, dq5, 是 设置
高 之后 一个 擦掉 或者 程序 运作, 或者 当 在 这
自动-选择 模式. 看 这 "重置 command" section, next.
看 也 "(所需的)东西 为 读 排列 数据" 在 这
"设备 总线 行动" 部分 为 更多 信息. 这
读 运作's 表格 提供 这 读 参数, 和
读 运作 timings 图解 显示 这 定时 图解.
重置 command
这 重置 command 将 是 写 在 这 sequence
循环 在 一个 擦掉 command sequence 在之前 erasing
begins. 这个 resets 这 设备 为 读 排列 数据. once
erasure begins, 不管怎样, 这 设备 ignores 重置 com-
mands 直到 这 运作 是 完全.
这 重置 command 将 是 写 在 这 sequence
循环 在 一个 程序 command sequence 在之前 程序-
ming begins. 这个 resets 这 设备 至 读 排列 数据.
once 程序编制 begins, 不管怎样, 这 设备 ignores
重置 commands 直到 这 运作 是 完全.
这 重置 command 将 是 写 在 这 sequence
循环 在 一个 自动-选择 command sequence.
once 在 这 自动-选择 模式, 这 重置 command 必须 是
写 至 返回 至 读 排列 数据.
如果 这 错误 状态 位, dq5, 变得 高 在 一个 程序 或者
擦掉 运作, writing 这 重置 command returns 这
设备 至 读 排列 数据.
自动-选择 command sequence
这 自动-选择 command sequence 准许 这 host sys-
tem 至 进入 这 生产者 和 设备 相等的
代号, 和 确定 whether 或者 不 一个 sector 是 保护.
这 command 定义 表格 5 显示 这 地址 和
数据 (所需的)东西. 这个 方法 是 一个 alternative 至 那
显示 在 这 自动-选择 代号 (高 电压 方法)
表格 4, 这个 是 将 为 prom programmers 和
需要 v
ID
在 地址 位 a9.
这 自动-选择 command sequence 是 initiated 用 writing
二 unlock 循环, followed 用 这 自动-选择 command.
这 设备 然后 enters 这 自动-选择 模式, 和 这
系统 将 读 在 任何 地址 任何 号码 的 时间,
没有 初始的 另一 command sequence.
powered 用 icminer.com 电子的-库 维护 版权 2003